|
METALS
Aluminum (for reflectors)
Pre-anodized hard-rolled pure aluminum sheet up to 99.9%
pure aluminum.
Aluminum (luminaire housing)
Formed
aluminum sheet deep drawing quality, 99% pure aluminum soft tempered, type
1050.
Aluminum
(control gear housing)
Die-cast aluminum alloy as per LM 24 Ref. BS# 1490/1988
with maximum Zinc content of 1%.
Aluminum (optical housing)
Spun 98% pure aluminum sheets of half hard quality.
Alloy 1050 or equivalent
Aluminum (housing)
Extruded aluminum alloy and anodized natural color at 15
microns for maximum corrosion resistance.
Alloy 6063T6.
Aluminum (reflectors for outdoor luminaires)
Formed high purity aluminum sheet, anodized with
3.5microns.
Material thickness: upto1.00mm, up to 99.9% pure Aluminum.
Industrial aluminum
General grade to Alloy 1050 + 114 or equivalent.
Cold-rolled sheet steel
General grade JIS G3141
Stainless sheet steel
General grade to 304 Standards.
Stainless spring steel
Ultimate tensile strength 1300 N/m2
Cold-rolled, Hard drawn
Grade: ASTM – A666
Hot dip galvanized sheet steel
Cold-rolled and hot-dip galvanized by the Sandzimir
process.
Coating thickness approx. 20microns.
Grade ASTM – A653.94
EGC Pressed Electro galvanized sheets
0.8mm thick sheet, 0.06oz/sq.ft.zinc coating on both
sides, phosphated and chromate sealing.
RUBBER & GASKET
EPDM Ethylene propylene rubber.
Max. temperature approx. 1200 C.
Excellent ageing characteristics.
CR.Chloroprene rubber (Neoprone)
Max. temperature approx. 1000 C.
Good ageing characteristics. Good oil resistance.
Q Silicon rubber
Max. temperature approx. 1500 C. Excellent
ageing characteristics.
Felt gasket
Water repellent type,
50% wool mixture and 220 Kg/m3. Density impregnated with
hydro-fobol and self adhesive tape. It
has a good heat resistance and elasticity.
Polyester
Gasket to polyester stuffing or laminated felt polyester.
Up to 30 Kg/m3 Foam density. Strong to compression.
EC 1055
Extruded oil soluble elastomer gasket.
Silicone
Sponge rubber according to I.S.O. 3302 E2.
|
GLASS
Glass sheet – Flat Glass
Silicate
glass, tempered.
Used where resistance to strong cleaning agents is
required, but where brittleness is of no consequence.
Glass (for floodlights)
Clear flat glass 3 to 6 mm thick, high heat resistance and
impact resistance of 2.5 ft-lbs. Transparency of not less than 90%.
Heat Tempered Glass
Clear
curved glass 4 to 6 mm thick, heat tempered with a minimum light transmission
of 90%. Maximum allowable working
temperature is 2500 C.
WIRE
- SILICONE GLASS FILLED WIRES max. temp. 1800
C.
- SILICON TEFLON INSULATED WIRES, max. temp. 1550
C.
- ECTFE RT WIRE (Halar) Fluorethene type
Max. temperature approx. 1550 C.
Excellent insulation properties. Insulates even after
fire.
Excellent mechanical properties (abrasion, indentation).
Chemically resistant to all known solvents.
Self-extinguishing.
- PVC (polyvinyl chloride) wire
Max. temperature approx. 1050 C. Single wire
conductor.
Often used for internal wiring in interior and industrial
luminaires
- PVC (polyvinyl chloride) wire
Max. temperature approx. 1050 C. Multi-wire
cable conductor
Often used for through wiring in interior and industrial
luminaires.
PLASTICS
PMMA
Acrylic (Polymetheyl Methacrylate)
Max.
temperature approx. 1000 C. Transmission grade 85-92%.
Extremely stable to weathering. Limited impact resistance.
ABS Acrylnitrile-butadena-styrene copolymer
Max. temperature approx. 850 C.
UP Glass reinforced polyester (GRP)
Max. temperature approx. 1500 Deg. C. Very high
tensile strength.
PA Polyamide (Nylon)
Max. temperature approx. 1000 C.
Very good chemical and mechanical properties.
PC polycarbonate (U.V. Stabilized with 50microns layer)
Max. temperature when subjected to UV radiation, approx.
900 C.
(Otherwise approx. 1200 C)
PP Polypropene (propene)
Max. temperature approx. 1000 C.
Good impact resistance and chemical resistance.
PS Polystyrene (styrene) UV-stabilized
Max. temperature approx. 750 C.
|
